hOpen Now
W R S
#

Crosby 3/8" G-450 Wire Rope Clip - #1010097

Crosby 3/8" G-450 Wire Rope Clip - #1010097Crosby 3/8" G-450 Wire Rope Clip - #1010097Crosby 3/8" G-450 Wire Rope Clip - #1010097
SKU: CR-1010097MPN: 1010097
$6.82
Quantity
  • USUALLY SHIPS: 1 - 2 Days
  • Made in the United States of America!

Product Description

  • The best-known wire rope clip in the industry
  • Each base has a Product Identification Code (PIC) for material traceability, the name CROSBY or CG, and its size forged into it
  • Achieves 80% efficiency of published wire rope breaking strength
  • Entire clip is galvanized to resist corrosion
  • Each is clip is bagged or tagged with proper identification information
  • Satisfies ASME B30.26 requirements
  • Meets Federal Specification FF-C-450 Type I, Class 1




Proper use of Wire Rope Clips
  1. Refer to the illustration below in following these instructions. Turn back specified amount of rope from thimble or loop. Apply first clip on base width from dead end of rope. Apply U-bolt over dead end of wire rope live end rests in saddle. Tighten nuts evenly, alternate from one nut to the other until reaching the recommended torque.
  2. When two clips are required, apply the second clip as near the thimble or loop as possible. Tighten nuts evenly, alternating until reaching the recommended torque. When more than two clips are required, apply the second clip as near the loop or thimble as possible, turn nuts on second clip firmly, but do not tighten. Proceed to Step 3.
  3. When three or more clips are required, space additional clips equally between the first two take up rope slack tighten nuts on each U-bolt evenly, alternating from one nut to the other until reaching the recommended torque.
  4. Apply initial load equal to loads expected in use. Inspect for proper orientation and spacing of clips and retighten the nuts to recommended torque.

Specifications

MPN
1010097
Model
G-450
Wire Rope Size
3/8"
Type
Forged
Overall Width
1.94"
Thread
0.44"
Clips Req'd Per End
2
Box / Case Quantity
100
Weight (lbs)
0.48

Questions & Answers

2 Questions & 2 Answers
Randolph
from Stanwood, WA asked:
March 8, 2020
What do you torque these to and how much weight will they hold using two on the end of 3/8" wire rope?  Also how much dead end cable do you suggest for clamping 3/8" wire rope?  I want to use two on both ends of my cables which will all be about 8ft long.
1 Answer
These 3/8" clips, when properly installed, have an 80% efficiency rating based on the catalog strength of common 6x19 or 6x37 class wire rope. For more details, including installation instructions, please view the PDF at this link.
Submitted by: WRS on March 8, 2020

Michael
from Plainview, NY asked:
January 9, 2020
Are these Buy America compliant for Federal projects?
1 Answer
No, these are not made 100% from American parts. The CM clip is, however, which you can view by clicking here.
Submitted by: WRS on January 9, 2020

Product Reviews

5.0
1 Reviews
5
100% (1)
4
0% (0)
3
0% (0)
2
0% (0)
1
0% (0)
0% Recommend this product (0 of 1 responses)
By Kris S.
Washington State
Perfect part for the job!
October 29, 2018
Quick shipping and a truly quality part. Not a low grade import. I trust these on my cables no question.
Pros
  • Top quality

Video

Attachments

Safety Notice

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov
Although Westech Rigging Supply strives to manufacture and sell the highest quality rigging and safety gear, use of the gear is dangerous if not used correctly by competent trained professionals. Westech Rigging Supply disclaims any liability resulting from the misuse of its rigging and safety gear. Please take a moment to more thoroughly review our disclaimer.

Westech Rigging Supply rigging and safety gear is only intended to be used by competent trained professionals. Misuse of the rigging and safety gear can result in serious injury up to and including loss of life. As such, Westech Rigging Supply disclaims liability for any misuse or incorrect product selection by our customers.

Rigging and safety gear purchased from Westech Rigging Supply should be used in strict accordance with all industry and OSHA standards. At no time should rigging or safety gear be used beyond its certified load ratings (aka Working Load Limits). Normal wear and tear should be expected with use of rigging and safety gear; therefore, all gear should be thoroughly inspected before each and every use. Worn or unsafe rigging and safety gear should never be used.