hOpen Now

Crosby 3/4" x 2" S-279 Machinery Eye Bolt - 7200 lbs WLL - #9900235

Crosby 3/4" x 2" S-279 Machinery Eye Bolt - 7200 lbs WLL - #9900235
SKU: CR-9900235MPN: 9900235
  • USUALLY SHIPS: 1 - 2 Days
  • Made in the United States of America!
  • This product is rated for overhead lifting.

Product Description

  • Forged steel, Quenched and Tempered
  • Working Load Limit shown is for in-line pull only
  • Recommended for in-line pull (capacity is reduced with angular loads)
  • Fatigue rated
  • Threaded UNC
  • Satisfies ASME B30.26 requirements


3/4" x 2"
WLL (lbs)
Safety Factor
Overall Length
Overall Width
Inside Eye
Weight (lbs)

Questions & Answers

4 Questions & 4 Answers
from Montreal asked:
December 13, 2019

In case if we have a concrete slab how do we fix the Crosby S279 in the slab?  Do we need something to install prior so we can fix it?

1 Answer
The answer is yes, you would need some sort of insert, but we do not have such a fitting to offer you.  Please also read below the response from Crosby, the product mfg.

"Crosby doesn’t have a presence in the pre-cast concrete market. All of our products are designed with bolting into, threading into, or even being welded to the load. If they can find some sort of embedded anchor that would also be compatible with the threads on our eye bolt, that would be acceptable. Currently, Crosby does not have any suggestions of who to seek out."

Submitted by: WRS on December 23, 2019

from WV asked:
August 4, 2018
Is it available with a longer shank?
1 Answer
This S-279 model from Crosby is only available in this exact size, but we do have another manufacturer that makes a similar product with different shank lengths. We will email you directly with available options.
Submitted by: WRS on August 5, 2018

from S. Lyon, MI asked:
December 30, 2017
Does this eye bolt (Crosby 3/4" x 2" S-279 Machinery Eye Bolt - #9900235) come in a smaller size? I need 5/16"-18 (can be any different pitch thread).
1 Answer
Yes, please visit the main Crosby S-279 Machinery Eye Bolt page where you can see all available sizes. Also, you may wish to check the "Attachments" tab for a downloadable PDF showing full specs for all sizes.
Submitted by: Westech Rigging Supply on December 30, 2017

from Michigan asked:
December 30, 2017
What is the thread description, as in diameter, pitch and length?
1 Answer
Crosby's S-279 eye bolts have standard UNC threads. The general size is called out as 3/4". The threads are cut 3/4"-10 and the overall length of the bolt area is 2.05". Please check the "Attachments" tab for a downloadable PDF showing full specs for all sizes.
Submitted by: Westech Rigging Supply on December 30, 2017

Product Reviews

1 Reviews
100% (1)
0% (0)
0% (0)
0% (0)
0% (0)
0% Recommend this product (0 of 1 responses)
By Blackbird
Sacramento, CA
Obvious Quality
August 8, 2019
Great experience. Clear website. Prompt shipment. Appropriate packaging. Quality product. What more could you want?



Safety Notice

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov
Although Westech Rigging Supply strives to manufacture and sell the highest quality rigging and safety gear, use of the gear is dangerous if not used correctly by competent trained professionals. Westech Rigging Supply disclaims any liability resulting from the misuse of its rigging and safety gear. Please take a moment to more thoroughly review our disclaimer.

Westech Rigging Supply rigging and safety gear is only intended to be used by competent trained professionals. Misuse of the rigging and safety gear can result in serious injury up to and including loss of life. As such, Westech Rigging Supply disclaims liability for any misuse or incorrect product selection by our customers.

Rigging and safety gear purchased from Westech Rigging Supply should be used in strict accordance with all industry and OSHA standards. At no time should rigging or safety gear be used beyond its certified load ratings (aka Working Load Limits). Normal wear and tear should be expected with use of rigging and safety gear; therefore, all gear should be thoroughly inspected before each and every use. Worn or unsafe rigging and safety gear should never be used.